Multipoint Locks·5 min field reference

How to Measure & Identify a Multipoint Door Lock

Replacing a European or American multipoint lock gearbox or full lock strip requires matching six critical dimensions, starting with Backset, PZ, Faceplate Width, and Deadbolt Throw. Measure in millimeters (mm) whenever possible.

Tools Needed on Site

  • Metric & Imperial tape measure or caliper (mm + inches)
  • Phillips #2 or Torx T15/T20 screwdriver (to inspect gearbox stamps)
  • Smartphone camera (to photograph faceplate logo & stamped codes)
4 Critical Multipoint Lock Measurements (Click Any Diagram to Zoom)
Bare Gearbox & Installed Door Views

1. Backset

35mm

Measure from the outer front edge of the metal faceplate strip to the exact center of the square handle spindle (or keyhole).

Common: 35mm · 45mm (1-3/4") · 55mm · 60mm (2-3/8") · 70mm (2-3/4")

2. PZ Center-to-Center

92mm (3-5/8") Standard Euro

Measure vertically from the center of the top handle spindle hub to the center of the circular section of the keyhole cutout.

Common: 92mm (3-5/8") Standard Euro · 70mm · 72mm · 85mm

3. Faceplate Width

16mm (5/8") Standard

Measure across the metal faceplate strip only. Do not include surrounding wood, fiberglass, or vinyl door slab thickness.

Common: 16mm (5/8") Standard · 20mm (25/32") · 22mm / 24mm U-Channel

4. Deadbolt Throw

14mm (9/16") Standard Throw

Extend the deadbolt fully and measure how far the bolt protrudes outward from the front face of the faceplate / door edge.

Common: 14mm (9/16") Standard Throw · 20mm · 25mm (1") Full Security Throw

Step-by-Step Measurement & Identification

  1. 1

    Measure Backset (Edge of Lock Strip to Center of Spindle or Keyhole)

    Measure horizontally from the front face of the metal faceplate (included in the measurement) to the exact center of the square lever spindle hole or keyhole. Common metric backsets are 35mm (1-3/8"), 45mm (1-3/4"), 55mm (2-3/16"), and 60mm (2-3/8"). American-standard multipoint locks also use 2-3/8" (60mm) or 2-3/4" (70mm).

    Backset can be measured on the removed lock body (left) or from the door edge to spindle center while installed (right).
    Field Tip: A 2mm difference matters: 45mm and 1-3/4" (44.5mm) are interchangeable, whereas 55mm vs. 60mm will misalign your escutcheon trim holes.
  2. 2

    Measure PZ (Center of Top Spindle to Center of Keyhole)

    Measure vertically from the center of the square handle hub (usually 8mm) to the center of the circular barrel of the Euro profile cylinder cutout (or thumbturn shaft). The overwhelmingly standard European PZ is 92mm (3-5/8"). Older patio systems occasionally use 70mm, 72mm, or 85mm.

    Measure center-of-spindle to center-of-cylinder barrel. Do not measure to the bottom of the Euro cylinder slot.
    Field Tip: For American-cylinder locks (above-handle deadbolt), measure center-to-center from the handle hub up to the tailpiece slot (commonly 3-5/8" or 5-1/2").
  3. 3

    Measure Faceplate Width (Metal Strip Only - Exclude Door Thickness)

    Measure strictly across the metal faceplate strip running down the edge of the door stile, excluding the wood, fiberglass, or vinyl door slab. Standard flat faceplates are 16mm (5/8") or 20mm (25/32") wide; commercial or uPVC doors sometimes use U-channel faceplates (22mm or 24mm). Note whether the top/bottom ends are square or radiused.

    Align zero with one edge of the metal faceplate strip. Most residential HOPPE, G-U, Fuhr, and Winkhaus locks measure 16mm (5/8").
  4. 4

    Measure Deadbolt Throw (Bolt Protrusion from Door Edge)

    Lift the handle and turn the key or thumbturn to fully throw the central deadbolt, then measure how far the deadbolt protrudes past the faceplate / door edge. Multipoint gearboxes are commonly manufactured in either a standard 14mm (approx. 9/16" or 1/2") throw or a full 25mm (1") security throw. Matching throw depth ensures the bolt seats cleanly into your jamb strike box without bottoming out.

    Ensure the lock is fully thrown before measuring. 1/2" (14mm) and 1" (25mm) throws require matching jamb strike pocket depth.
    Field Tip: HOPPE HLS9000 and G-U gearboxes frequently offer both 14mm (1/2") and 25.4mm (1") deadbolt throw versions in the exact same 35/92 or 45/92 backset!
  5. 5

    Identify Auxiliary Locking Points & Centerline Positions

    With the lock extended, identify the auxiliary locking points above and below the central gearbox: Tongues (wedged blades), Shootbolts (vertical rods exiting top/bottom of door), Rollers/Mushrooms (cams), Hooks, or Roundbolts. Measure from the center of the handle spindle up to the center of the top locking point and down to the bottom locking point.

  6. 6

    Verify Operation Mode & Handle Height

    Check how the multipoint bolts engage: Lift-Lever (Manual) requires lifting the handle upward before turning the deadbolt; Key-Wind / Automatic engages multipoints via key/thumbturn or slam-shut triggers. Finally, measure from the bottom of the door panel to the center of the handle spindle (commonly 36" / 914mm).

Common Multipoint Lock Brand & Series Reference

Swipe →
Manufacturer / SeriesTypical FaceplateCommon BacksetsStandard PZIdentifier Stamp
HOPPE HLS9000 / HLS716mm (5/8") SS35mm, 45mm, 60mm92mm (3-5/8")HOPPE logo or HLS stamp
G-U / Ferco (Europa, Secury)16mm flat35mm, 45mm, 55mm92mmG-U, FERCO, or 6-xxxxx code
Fuhr (855, 856, Multisafe)16mm or 20mm35mm, 45mm, 55mm92mmFUHR oval logo on faceplate
Winkhaus (Cobra, Thunderbolt)16mm flat35mm, 45mm92mmWH three-house emblem
AmesburyTruth / Pella / Andersen5/8" or custom45mm, 2-3/8", 2-3/4"92mm or 3-5/8"AT, Truth, or OEM 2-pt/3-pt stamp
Endura / Trilennium (3000)7/8" one-piece2-3/8" or 2-3/4"American cylinderThree spring-loaded I-bolts

Service Technician Notes

  • ▸Can you replace just the center gearbox? On many modular HOPPE HLS9000, G-U Secury, Winkhaus, and Fuhr locks, the center lock case unbolts from the faceplate, saving shipping cost and door prep.
  • ▸Latch reversal: Almost all multipoint center latches are reversible for inswing/outswing by pulling a small release tab or loosening a set screw on the back of the case.
  • ▸Never force a stiff multipoint handle. 90% of broken gearboxes are caused by door sag misaligning shootbolts or tongues against strike plates. Adjust your 2D/3D hinges simultaneously.

Browse Matching Replacement Hardware

Frequently Asked Questions

What does 45/92 mean on a multipoint door lock?

45/92 indicates a 45mm backset (from faceplate front to handle spindle center) and a 92mm PZ (center-to-center distance from the handle spindle to the Euro cylinder circular keyhole).

My multipoint lock brand is discontinued. Is there a retrofit kit?

Yes. We stock direct replacement kits for discontinued Atrium/G-U Tripact, older Fuhr, Peachtree, and HOPPE HLS7 systems. Upload a photo of the faceplate stamp and upper/lower locking points on our Quote Form and our team will specify the exact conversion kit.

Have Your Measurements Ready?

Submit Measurements or Photos for Exact SKU & Trade Pricing

Our North Kansas City specialists respond within one business day with verified part compatibility and volume pricing.

More Technical Guides