Hinges & Handing·4 min field reference

Door Handing Chart (LH, RH, LHI, RHI, LHO, RHO) & Adjustable Hinge Guide

Ordering handed multipoint trim, mortise locks, or adjustable lift-off hinges requires consistent handing terminology, plus knowing the difference between Horizontal Guide (H) hinges and Vertical Set (V) hinges on heavy entry and patio doors.

Tools Needed on Site

  • Tape measure (for leaf width × leaf height & mortise pocket depth)
  • Hex Allen key (typically 3mm, 4mm, or 5/32" for hinge adjustment caps)
  • Corner radius gauge or coin (penny = ~3/8", dime = ~1/4", nickel = ~5/8" diameter check)
Key Field Measurements DiagramNot to scale · Verify in mm / 1/16"
LHI (LH)Stand Here (Ext)RHI (RH)Stand Here (Ext)LHO (LHR)Stand Here (Ext)RHO (RHR)Stand Here (Ext)

Step-by-Step Measurement & Identification

  1. 1

    Determine Door Handing from the Exterior (Keyed Side)

    Stand OUTSIDE the building facing the exterior of the closed door: If hinges are on your LEFT and the panel swings IN toward the room, it is Left Hand Inswing (LHI / LH). If hinges are on your RIGHT and it swings IN, it is Right Hand Inswing (RHI / RH). If hinges are on your LEFT and the door swings OUT toward you, it is Left Hand Outswing (LHO / LHR). If hinges are on your RIGHT and it swings OUT toward you, it is Right Hand Outswing (RHO / RHR).

    Field Tip: Caution with Andersen Hinged Patio Doors: Andersen traditionally hands doors from the EXTERIOR based on which side the doorknob/handle is on, OR calls hinge-left inswing 'Left Hinged'. Always state both hinge side viewed from outside AND swing direction on quote requests.
  2. 2

    Distinguish Guide Hinges (H) vs. Set Hinges (V)

    Many European/OEM 2D adjustable hinges (HOPPE Columbus, HTL, Fuhr, Truth Sentry, V400) split vertical and horizontal duties between two hinge types on the same door: SET Hinges (marked 'V' or with a bottom Allen jack screw) support the vertical weight of the slab and adjust height; GUIDE Hinges (marked 'H') adjust horizontal side-to-side reveal. Newer 'All-in-One' 3D hinges combine both adjustments in every hinge.

  3. 3

    Check Standard 3-Hinge & 4-Hinge Panel Placement

    On a 3-hinge door using separate H/V hinges, the middle hinge is typically the Set (V) load-bearing hinge while top and bottom are Guide (H) hinges (verify OEM spec, as some systems place Set hinges top & bottom). All-in-One 3D hinges eliminate position mix-ups.

  4. 4

    Measure Leaf Size, Corner Radius & NRP Security

    Open the hinge flat and measure total width across both leaves × vertical height. Common adjustable sizes are 3-5/8" × 3-5/8", 3-5/8" × 4", and 4" × 4". Check corner profile (Square, 1/4" radius, or 5/8" radius) and confirm Non-Removable Pin (NRP / set screw in barrel) for all outswing exterior doors.

Door Handing Quick Cross-Reference (Viewed from Exterior)

Swipe →
Hinge Side (Viewed Outside)Swing DirectionTrade CodeArchitectural Reverse Code
Hinges on LEFTSwings IN (away from you)LHI (Left Hand Inswing)LH (Left Hand)
Hinges on RIGHTSwings IN (away from you)RHI (Right Hand Inswing)RH (Right Hand)
Hinges on LEFTSwings OUT (toward you)LHO (Left Hand Outswing)LHR (Left Hand Reverse)
Hinges on RIGHTSwings OUT (toward you)RHO (Right Hand Outswing)RHR (Right Hand Reverse)

Service Technician Notes

  • ▸Replacing discontinued HOPPE Columbus 2D hinges: Current All-in-One 3-5/8" × 3-5/8" and 3-5/8" × 4" adjustable hinges are designed to match standard mortise pockets. Check screw hole pattern before routing.
  • ▸Always adjust vertical Set (V) hinges equally when a door has multiple Set hinges so one barrel doesn't carry 100% of a 150 lb insulated glass slab.

Browse Matching Replacement Hardware

Frequently Asked Questions

How do I tell 1/4" radius vs. 5/8" radius hinge corners?

Place a U.S. quarter against the rounded corner of the hinge leaf: if the curve matches the curve of a quarter closely, it is a 5/8" radius corner. If the corner is much tighter (closer to a dime's edge), it is a 1/4" radius corner.

Do outswing exterior doors require special hinges?

Yes. Because the hinge knuckle sits on the exterior of an outswing door, always specify Non-Removable Pin (NRP) or security stud hinges so an intruder cannot tap out the hinge pin.

Have Your Measurements Ready?

Submit Measurements or Photos for Exact SKU & Trade Pricing

Our North Kansas City specialists respond within one business day with verified part compatibility and volume pricing.

More Technical Guides